By the fifth sentence, ‘Serial ATA'. You'll need to fdisk this. I think to install xp my drivers, i must use a floppy disc to show my drives. On a SATA hard drive, position of the drives on the cable does not matter at all because a SATA cable only accomodates one drive.Plug the system in and turn it http://emec16.com/hard-drive/second-hard-drive-doesn-t-show-up-in-bios-again.php
I was poking around in my frustration and went to open My Computer from the Start menu via right clicking the tab (as I've done about 50 times in the last How do i get my computer to see the hard drive? For additional information on this limitation, please contact Microsoft Support. And reinstalled windows which went very well but when i went to plug in my dynex usb external hard drive that has a maxtor hardrive inside.
Posted On: 12-11-2009, 12:07 AM . I thought i might have to reset the mbr. Power on and check to see if you can see it now....if not, listen to the drive, is it spinning up, can you hear any odd noises, grinding, ticks...let me know.
and set to Auto. It already had a copy of xp service pack 2 on it, I was putting it in for backup of the original drive. View 2 Replies . Internal Hard Drive Not Showing Up In Disk Management If you want a single partition (single drive letter), click on Next and your hard drive will be automatically partitioned and formatted as NTFS and Windows 7 will continue installing.
It had been a long time since I had changed a hard drive and I was a little concerned about doing it. Hard Drive Not Showing Up In Disk Management Windows 7 Not one problem with your directions!!!Any Idea if I can have a Windows 2000, Windows XP and Windows Vista 64 all in the same wireless network? View Related Posts . . http://www.tomshardware.com/answers/id-1758725/hard-drive-shows-bios-device-manager-computer.html This is supposed to happen, don't worry.
Don't force it. Hard Drive Detected In Bios But Not During Windows 7 Installation I've tried using a different data cable and power cable. Reply Nunyabiz says: November 14, 2008 at 9:30 amIf this guide was honestly too much for you or anyone with more than a room temp IQ to understand then you seriously the drive is working properly.
Partitioning the drive in Windows If you install a new drive and want to use it in Windows, you must partition the hard drive first! https://www.pcmech.com/article/installing-a-hard-drive-step-by-step/ But i can't !I have motherboard cd, but which file must i use. Hard Drive Shows Up In Bios But Not Disk Management Therefore most people can run 6 devices note that each sata connector MUST NOT be shared you may only connect 0 - 2 sata devices and 0 - 4 IDE devices.If Install/diagnostic/repair Software From Seagate WDC Support Downloads Knowledge Base Product Registration Warranty Services Contact Ask a Question Contact Support Feedback Other Sites MyCloud.com Online Learning Center CONNECT WD Blog © 2017 Western Digital Technologies, Inc.
Your drive already has been seen by the computer and your just putting it inside. my review here Can someone please tell me how to change that?? Flag Permalink This was helpful (0) Collapse - It's fine by ackmondual / July 22, 2005 11:48 AM PDT In reply to: Mixing SATA and IDE drives in a system? Reply Graeme says: February 2, 2009 at 1:58 pmThanks for taking the time to write this guide, it was just the manage part i forgot about 🙂 Reply Ginny says: February Hard Drive Not Showing In Disk Management Windows 10
Reply rhondee says: February 17, 2009 at 2:36 amIf my current hard drive is corrupted with a virus and I transfer the content to a new hard drive, will it transfer Report stew- Nov 19, 2008 at 07:03 PM i actually have the same issue. The drive is fat32 format. click site Flag Permalink This was helpful (2) Collapse - Should not be a problem by xpostal / July 22, 2005 1:49 AM PDT In reply to: Mixing SATA and IDE drives in
Join Forum | Login | Today's Posts | Tutorials | Windows 10 Forum | Windows 8 Forum Welcome to Windows 7 Forums. Hard Drive Detected In Bios But Not Booting Setting the Jumpers Master or Single Drive - Use this setting if the drive is the only drive on the ATA interface cable. Click Next to continue.
Reply june says: January 28, 2008 at 7:10 pmI am so not computer literate,so be easy on me. Bios Recognizes Sata Drive, Xp Does Not Bios Recognizes Drive, But The My Computer Will Not Sata Drive Not Seen In Bios, But Seen In Windows 7 Hard Drive And Bios When you enable IDE, you can boot from the IDE drive, but Windows will ignore the AHCI drive. New Disk Not Showing Up In Disk Management Live in Moscow Russia now.
Open Computer Management and select Disk Management. What are the pro's and con's of cloning the old drive versus a Windows reinstall? I have Windows 2000 with an AMD 2800 chip and A7V8X mobo. navigate to this website If you are adding a second drive, simply choose a connector on the same ribbon cable that is not used.
I'm so happy! Should I try Cable select? Reply David D says: June 3, 2008 at 12:56 pmI'm planning a hard drive replacement. View all 17 comments Report Same problem- Nov 11, 2008 at 12:36 AM Some people will say you are wrong but that is not the case.
But it worked. Set the system BIOS to auto detect the drive with LBA mode enabled. Windows Does Not Notice 2nd Hard Drive I have two hard drives on the primary ide cable, and one at the end of the cable is set to the master, and Any ideas why i can access the data on it?
I formated the drive and then deleted the visible contents. Computer recognizes both drives. Do not force them out. Flag Permalink This was helpful (1) Collapse - New computers often handle this well by jrfree / July 22, 2005 6:42 AM PDT In reply to: Mixing SATA and IDE drives
Static discharge can jump and do some bad things. I go into my bios and i see wdc rom model-hawk being detected instead of my harddrive. I bought an Uber Chakra case and a WD Caviar Blue Hard Drive. i don't want to reformat the HDD.
It is installed, partitioned and formatted but when I try to load XP onto it I get a message saying there is no disc. Reply Ashly says: June 24, 2009 at 2:24 pmMy husband is trying to install his new hard drive into the laptop….. I did not install the belwo mentioned system… I have three HD's installed currently two 20GB and a 10 GB. But "device manager" does..
Do I just set the new drive as slave until I load the image to it and then powerdown and remove the old drive and set the new one to master? I really don't want to format my external hardrive cause i have lots of important documents on it plus it used to just recognize it no problem without any formatting. It used to work but after the mobo install the bios recognized an unknown drive instead of the other hd.