Another, working, computer. If the key stroke required to enter CMOS Setup isn't displayed on the screen as the PC begins to boot, you'll need to look it up in the documentation or on The SATA drive can be the secondary drive? There are a few additional considerations to take into account if you are running multiple SATA drives in a RAID array (like making sure all OS's are installed with RAID drivers) Check This Out
By this, I mean duplicate the entire hard drive, and each partition.Acronis will allow you to custom size your new drives partitions, as it is likely a bigger drive, or at Even two different brands of drives won't work without other procedures.. Just use the power plug you have, no worries. if you can help me.I have a Widows 2003 Server Edition that`s very important.
Boards with mulitple SATA connectors and a single PATA connector are still around. The one below has a SATA data cable connector plug, combined with both kinds of power plug connectors. Prior settings of the jumpers to "slave" would result in no boot screen at all upon powering on. more stack exchange communities company blog Stack Exchange Inbox Reputation and Badges sign up log in tour help Tour Start here for a quick overview of the site Help Center Detailed
go to Control Panel/Admin. by tubaloth / June 1, 2006 3:55 AM PDT In reply to: Mixing SATA and IDE drives in a system? Return to Diagnostic Chart SMART is one of those cute acronyms you don't want to see popping up on your screen with a nasty message. Ide Hard Drive Jumper Settings To its right is the SATA power plug.
Return to Diagnostic Chart Have you updated the firmware for your SSD drive? Ide And Sata Drives In Same Computer nothing happens.I can not BOOT because my PC does not recognize the boot sector..or something.All the data it`s on my SATA HDD, i can acces it by putting the HDD into Du kan ändra inställningen nedan. If neither fix helps, try disconnecting the data cable to ensure that the drive isn't receiving some flaky power down signal from a bad ATA interface or a crazy power management
The adapter has only one SATA connector. Use Ide Drive With Sata Motherboard There are two things to keep in mind, do not overload your power supply or strange difficult problems will begin to occur and make the correct BIOS settings for your data neither of this partitions let me install windows as they say it cant read the SATA drive.> the third thing that i found really weird was that when i reinstalled windows Return to Diagnostic Chart Are the ribbon cable connectors and the IDE ports on the drives and the motherboard keyed such that the cable can only go one way?
Flag Permalink This was helpful (0) Collapse - Lost half my SATA drive by PennT / July 26, 2005 6:08 PM PDT In reply to: Mixing SATA and IDE drives in Also please exercise your best judgment when posting in the forums--revealing personal information such as your e-mail address, telephone number, and address is not recommended. How To Connect Ide Hard Drive To Sata Motherboard Pay attention to the "Volumes to include" section if you decide to use this process as you only want to take an image of the external drive. Sata And Ide Hard Drives Together I've used Syba's IDE/SATA Converter.
This post has been flagged and will be reviewed by our staff. his comment is here Just search on "IDE to SATA" at Amazon. The catch is i dual boot from that drive and I'd like both operating systems (XP and 7) to continue to be bootable... I am able to boot from a SATA drive with this motherboard just fine, and I plan to use Acronis TI 2010 to clone my IDE drive. Motherboard With Ide And Sata Ports
Beg Borrow or Steal. Just take whichever tools you need from the toolset to USB-connect your drive and power it. (The toolset does not include a drive enclosure, so you'll want to buy that separately Logga in om du vill rapportera olämpligt innehåll. http://emec16.com/hard-drive/can-t-access-2nd-sata-drive-after-reformat.php You cannot mix the two on the same controller to my knowlege.
Can't find your answer ? How To Install Ide To Sata Converter Do those IDE converters to SATA work ? Join thousands of tech enthusiasts and participate.
The adapter is equipped with a switch and a jumper to select which mode to use (described above). These sub-standards represent continuing improvement in data transfer speed and reliability. Throughout this evolution, IDE's physical connectors have remained the same. trainmaster5May 13, 2008, 1:49 PM I just cloned my old Maxtor 250gb PATA to a Seagate 500gb SATA. How Many Hard Drives Can Be Connected To A Single Ide Cable Two hard drives are connected: a 1 TB SATA disk and a legacy 160 Gig IDE drive connected with Syba.
Return to Diagnostic Chart Is the SSD drive equipped with a SATA or PATA (IDE) interface? Convert all partitions on IDE HDs to extended. (This option maybe optional)2. Russian Nesting Words In which countries is Russian useful for anglophone tourists? http://emec16.com/hard-drive/laptop-no-longer-sees-2nd-sata-drive.php I picked up a 160GB SATA drive and I wanted to "clone" the IDE (which is bootable) to the SATA.
I installed Windows on the SATA drive.I built this computer myself and haven't had any problems with this configuration. I will give it a try later tonight or tomorrow some time and post back the results. Using a connect that converts the IDE to SATA, the bios (ClickBiosII) doesn't detect it. When the PC powers up, you should hear the hard drive motor spinning up the drive and the gentle clunking sound of the read/write head seeking.
You will no longer be using Norton Ghost, nor will you want to any more. (I've used Ghost 2003 since 2003, but using it with SATA drives is a nightmare at Storage forum About This ForumCNET's Forum on storage is the best source for finding help, troubleshooting, and getting buying advice from a community of experts. If you don’t know the model number you can use CPUID and locate the model number and manufacturer on the “Mainboard” tab: In this example, the manufacturer is MSI (Micro-Star International), Apr 2, 2010 #10 EXCellR8 The Conservative Topic Starter Posts: 1,835 Okay well i finally completed the rebuild, and my motherboard and OS are treating the SATA drive as IDE...
Läser in ... What I mean to say is Windows sees all HDD's as either IDE or SCSI, and it'll see SATA drives as IDE most times. but I guess it may exist for reasons such as this so you never know. Once you have that figured out you need to type this dism /image:c:\ /add-driver /Driver:X:\ /recurse Replace “X” with the drive letter from the previous step: Hit enter and it should
Yvo ro 19 870 visningar 2:31 Disco SATA en Board IDE - Längd: 8:50. Or just test the configuration you want. Once I cloned the structure of the old IDE drive to the new SATA unit with True Image, I booted from the copy and it worked perfectly! This chart summarizes the three drive integration solutions I've described: USB Toolset: Drive Dongle: Controller Card: Mounts Drive(s): External Internal Internal & External * Requires Software Driver: No No Yes Supports
Try swapping the power lead for a spare or one used by another drive. To learn more, read the Wikipedia entries on PATA, SATA, and disk storage. Anyway, the mobo only has 1 IDE slot...which is being used for my CD/DVD burner...my thoughts was to slave the IDE drive to the SATA, is this right?