Home > How To > HOw To Directly Address 2nd PC On The Client Router

HOw To Directly Address 2nd PC On The Client Router

Contents

Password Advanced Search Show Threads Show Posts Advanced Search Go to Page... I then recreated it exactly as it was, and Voila! A week ago my network configuration was fine all computers are identified by the server, I can print from the network and the tinasoft running smothly. A new router's basic settings Though the design of the web interface is opened varies from one vendor to another, most of them have granular menus. have a peek here

Linksys routers can't be configured as bridge or repeater. November 30, 2008 at 2:06 PM Alan said... Both routers are using 192.168.0.1 as their own address. Wow, this is just fabulous.

Find All Routers On Network

An IP address from the first router's LAN is not valid in the second router's LAN.It is important to connect those wireless routers through their LAN ports, turn off the DHCP Linksys WRTs with Linksys firmware do not connect wireless to other routers, they don't operate as wireless bridge. You have two routers with two access points which connect to two different ethernet LAN. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build.

it stays with the weak signal too long until it looses connection instead of roaming earlier. dynamic DNS service, access restrictions, ...Bottom line: unless you have good reasons why you must have some computers separated from the other computers in your network, there is no good reason But in this case, you connect LAN to LAN, thus the DHCP request from the sky router will arrive to the Virgin router - because technically the LAN interface (and wireless) How To Find Second Router Ip Address You'll find similar answers with some screenshots in the Linksys Easy Answers, e.g. 4579The setup:1.

Once you have accessed it, the rest -- at least most of it -- is self-explanatory.Most routers' web interfaces are similar and self-explanatory. Article Getting a "Limited or no connectivity" error or in Windows? Just note, I was unable to find the exact model you specified as your router. http://superuser.com/questions/1013686/accessing-router-from-another-router-modem SkyRouter will record 192.168.0.1 as the gateway address to VirginModem segment.

set a LAN IP address of 10.0.133.2 and LAN subnet mask 255.255.255.224.c. Wifi Ip Address Hack All connected through Linksys wireless router. July 27, 2009 at 2:28 AM Eli said... I'll just leave it like that since this Sonicwall has been a solid device for me over the years and see no technical advantage of using the linksys router instead.

Second Router Ip Address

gv thanks for the response,,,,here are the settingsMicrosoft Windows [Version 6.0.6000]Copyright (c) 2006 Microsoft Corporation. Get More Info share|improve this answer answered Sep 12 '16 at 1:53 Jawad 1 add a comment| Your Answer draft saved draft discarded Sign up or log in Sign up using Google Sign Find All Routers On Network Great post! How To Find Ip Address Of Router Connected To Another Router Ask a question Member requests are more likely to be responded to.

I would highly recommend to get the wireless internet radio working properly with encryption enabled. navigate here But often there's an easier way to configure a device as slave. Works like a charm. Article What to Do When Your Home Network Router Isn't Working Article Need help with your home network router installation? How To Access Secondary Router

Also note the reset button, which brings the router's settings to default value. Port 7 is where my D-Link wifi router is plugged into. If you have your wifi turned on and you are also connected over ethernet to router 1, your wifi may be taking precedence. Check This Out I am NOT using the wan port on router 2 May 21, 2008 at 2:54 PM gv said...

December 14, 2007 at 8:03 PM gv said... How To Get Ip Address Of Wireless Router The network shares the printers and some shared software/files from the host computer. My system looks like this: http://i.imgur.com/U3dK2SQ.png So the router 2 is connected to the line.

I can make Wireless to obey Firewall-DHCP, but after doing so it seems I have no other way to connect to Wireless web interface (to setup anything, if required later) but

And lack of information on a potential server. Click OK and you now have a network sharing folder. Once you have gotten these two pieces of information, just type the router's IP address in the address bar of a browser on a connected computer, press Enter, and then enter How To Connect A Router To Another Router Wirelessly All you need is a computer that has a network port (most computers do) and two network cables (a new router comes with at least one network cable).

If there are teenagers in your proximity their parents may not like it very much if you run a open access point. About CNET Privacy Policy Ad Choice Terms of Use Mobile User Agreement Help Center make-use-of-logo logo-background menu search search-start close email bookmark facebook google twitter pinterest stumbleupon whatsapp amazon youtube youtube May 21, 2008 at 1:10 PM gv said... this contact form It might seem like a daunting task to set up a new home router.

It only affects traffic between the internet port and the LAN. hi gv. The whole configuration becomes more complicated: you always have to think about where to configure what, e.g. Disabled? - Define the Default Gateway to be the primary/1st Router/in-AP-mode ?

If you use the internet port on the second router you do not follow the suggested setup in this post. September 11, 2008 at 1:47 AM gv said... The internet port of the router is a different side. Since the private network address of SkyRouter is also non-configured, SkyRouter too would use the default private network address of 192.168.0.x.

If you want to use a wireless router as simple access point and connect one of its LAN ports to the main router (nothing connected to the internet port of the One has a printer it's sharing without a password. Let's presume the modem and its wireless router are not integrated. The last resort All routers come with a reset button.

September 19, 2008 at 6:31 AM gv said... However, computer B cannot ping A. On the first router, leave IP address 192.168.1.1 and connect the internet port to the modem. Configure the router at http://192.168.1.1/3.

Is it the case that it only hops when the weaker signal goes away entirely? Helpful +2 Report suman Mar 18, 2009 06:24PM Thankyou, Now I m able to ping my window m/c from unix.